Doepfer A-123-2

Description:

Doepfer A-110-6, Eurorack Module, Trapezoid Thru Zero Quadrature VCO, Uses quadrature trapezoid as the fundamental waveform, Features linear Thru Zero frequency modulation and quadrature outputs for all waveforms (two 90 degree out of phase signals... More

Description:

Doepfer A-101-6, Six Stage Opto FET VCF, New filter module in which so-called opto FETs are used to control the filter frequency, Dimensions (W x D): 40.3 mm (8 HP) x 65 mm, Power requirement: 40 mA More

Description:

Doepfer A-162, Dual Trigger Delay, Allows delayed output of the input signal, Power requirement: +40 mA (+ 12V) / -0 mA (-12V), Width: 8 HP / 40.3 mm, Depth: 45 mm (measured from the back of the front panel) More

Description:

Doepfer A-149-2, Eurorack module, Expansion module for the A-149-1 (Article Nr: #199098#), Supplies 8 digital, random voltages, Eurorack format, Width: 4 HP, Depth: 35 mm, Power requirement: +40 mA (+ 12V) / -10 mA (-12V)@+*Note:* Must be mounted... More

Description:

Doepfer A-106-5 SEM Filter, Filter, 12 dB Multi-mode filter, in which the circuit of the SEM module is used, Width: 8HP 40.3 mm, Depth: 55 mm (measured from the rear of the front panel), Power requirements: +30 MA (+ 12V) / -20 mA (-12V) More

Description:

Doepfer A-199 Spring Reverb Module VE, Spring reverb module in Eurorack format, By way of spiral springs electronically recreates the reverb effect, Spring system with 3 separate springs, Reverb signal can be fed back to the input, Width: 8 HP, Depth:... More

Description:

Doepfer A-160-5 VC Clock Multiplier, Voltage Controlled Clock Multiplier, Multiplication factor can be controlled by control voltage or a regulator, Width: 4 HP, Depth: 35 mm, Power requirements: +50 mA (+12 V) / -0 mA (-12 V) More

Description:

Doepfer A-143-9, Quadrature LFO / VCO, Can simultaneously produce sine and cosine signals, 4 Outputs that are phase shifted by 90 degrees, Eurorack format, Width: 8 HP, Depth: 50 mm, Power requirement: +30 mA (+ 12V) / - 30 mA (-12V) More

Description:

Doepfer A-155, Analog-/ Trigger Sequencer, 2 Switch rows with 8 steps each, Eurorack format, Width: 50 HP, Depth: 40 mm, Power requirement: +80 mA (+ 12 V) / -20 mA (-12 V), Optional expander module: Article Nr #192018# (not included, must be ordered... More

Description:

Doepfer A-154 Vintage Edition, Sequencer Controller Module, Vintage edition with black front plate, Expansion module for A-155 (Article Nr #154958#), Different operating modes, LED display, 8 or 16 sequencer steps, Controls up to 2x A-155 (2x A-155 are... More

Description:

Doepfer A-155 Vintage Edition, Analogue and Trigger Sequencer, Vintage edition with black front plate, 2 Switch rows with 8 steps each, Euro rack format, Width: 50 HP, Depth: 40 mm, Power consumption: +80 mA (+12V)/ -20 mA (-12V) More

Description:

Doepfer A-101-2 Vactrol Lowpass Gate, Vactrol lowpass gate, Combination of low-pass filter (LP) and VCA, Based on the idea of the Buchla module 292, The frequency (in LP mode) or the amplitude (in VCA mode) can be controlled manually (F / A) and via 2... More

Description:

Doepfer A-128, Fixed Filter Bank, 15 Parallel bandpass filters, Amplitude controller per band filter, Width 20 HP, Depth: 60 mm, Power requirements: +20 mA (+12 V) / -20 mA (-12 V) More

Description:

Doepfer A-118 Noise/Random, Noise/Random Voltage Generator@+Module A-118 is a noise and random voltage generator. It produces the following signals: white noise, coloured noise, and random voltage. White and coloured noise can be used as audio signals,... More